Skip to content

← Firmware Downloads

Firmware release notes · Reborn (Y2Linux) · Y2

Y2Linux 1.0 Beta 9.3.12

Reborn (Y2Linux) 1.0 update for the Innioasis Y2. Download it below, or let Updater CE install it for you.

Debian-based Linux with a fast clickwheel interface for the Innioasis Y2.

baseline-220Y22026-11-04schulzcode/y2linux

Download this release

Y2Linux 1.0 Beta 9.3.12: Bluetooth pauses and skips like a phone. Linux 6.18 and the native Reborn music player for the Innioasis Y2.

Already running Y2Linux

Settings → System → Software Update → Update Now (on Beta 9.2.8 and older: Settings → About & Updates → Check for Updates → Update Now).

What changed

Beta 9.3.7 kept a Bluetooth stream open while you paused, so that no headphones would be asked to stop and start. Phones never do that, and it caused three complaints at once: silence after a pause or after the second or third song (#89), the connection drop about 20 seconds into a pause (AirPods Pro), and Buds that "disconnected" a minute into a pause (#90, where the player had in fact gone to sleep). This release goes back to what phones and Beta 9.2.16 do.

Before release: the platform's full check, Reborn's workspace tests (new ones for the paused-headset hold and the kept Bluetooth sink) and the 552 tests of the release images. On the developer's player with AirPods Pro: skips in a row and pauses of various lengths, all with sound afterwards. A capture of the previous test build showed the packets to the headphones running on without a gap at the skips and silence only after the pause/resume gaps, which is what settled the cause. Other headphones were not re-tested yet: if yours behave worse than in 9.3.7, please send an error report.

What changed and why, in plain words: Beta 9.3.12 report. Versions 9.3.8 to 9.3.11 were unpublished test builds; everything from Beta 9.3.7 is included (Beta 9.3.7 report).

Install (from stock)

You need SP Flash Tool v5.2032, a USB cable, Y2Linux-1.0.0-beta.9.3.12-first-install.zip below and the Innioasis Y2 firmware package v3.2.0 from Innioasis (only this version works; it is also your way back to stock).

  1. Unpack both.
  2. SP Flash Tool → Download Only → load MT6582_Android_scatter.txt from the Y2Linux zip. Exactly BOOTIMG, RECOVERY, ANDROID and USRDATA are ticked.
  3. Click Download and connect the switched-off Y2; wait for the green tick.
  4. Unplug and press Power: the player sets up its Internal Storage (a few seconds), then Y2Linux and Reborn start, music works.
  5. Connect the Y2 to the computer and copy (don't move) system.img from the Innioasis package into the Firmware folder on Internal Storage. The player takes the Wi-Fi/Bluetooth firmware from it and turns the radios on.

Full guide: INSTALL · How updates work: Recovery and updates · Storage: Storage · Audiobooks · Headphone settings: Headphone output · Error reports · Skins: skin guide

Known issues (beta)

Files

Beta software: use at your own risk. Not affiliated with Innioasis, MediaTek, Awinic, Last.fm, AutoEq, Strawberry or Google. Noto Sans CJK is licensed under the SIL Open Font License 1.1. Details: Beta 9.3.12 report.

Sources unchanged since an earlier release

Updating to Reborn (Y2Linux) 1.0

The same steps install this release for the first time or replace the build already on the player. Back up your music before you start.

  1. Check the model and type

    Confirm the player is an Innioasis Y2 before downloading. Y1 players come in two hardware revisions, Type A (software 2.0.0 or later) and Type B (earlier software); the two ROMs are not interchangeable.

  2. Download the package built for your computer

    Use Updater CE for the guided route, or download the portable package for Windows, macOS or Linux from this page. The release's own ZIP is also listed for manual flashing.

  3. Connect the player while it is switched off

    Use a data-capable USB cable and connect the player only when the installer asks. Keep it connected until the flash reports success.

  4. Verify the version after it reboots

    Open the player's Settings or About screen and check that it reports Reborn (Y2Linux) 1.0.

Install Reborn (Y2Linux) 1.0 on your computer

Pick the guide for the computer you will flash from. Each one names the exact package, its size and the steps that machine needs.

Windows

Install on Windows

Windows 11 and Windows 10 are supported; the legacy ZIP is for Windows 7/8 and 32-bit Windows, and Windows on ARM runs its own build natively.

363 MB · 135 MB

macOS

Install on macOS

The macOS package is universal: it runs on Apple silicon and Intel Macs.

178 MB

Linux

Install on Linux

Use the x64 build on an ordinary Intel or AMD desktop, the arm64 build on a Raspberry Pi or other ARM board, and the legacy ZIP on 32-bit Linux.

408 MB · 241 MB · 134 MB

Questions about this update

How do I update Innioasis Y2 to Reborn (Y2Linux) 1.0?

Download the package for your computer from this page, or open Updater CE and choose Reborn (Y2Linux) 1.0 for Innioasis Y2. Connect the player while it is switched off, then let the installer finish and let the player reboot.

Is Reborn (Y2Linux) 1.0 the latest Reborn (Y2Linux) release?

The release list on this page is ordered newest first, so the top entry is the latest published build. Preview and nightly builds are labelled as such.

Can I install Reborn (Y2Linux) 1.0 from another computer?

Yes. Download the ZIP here, copy it to the computer that can talk to the player, and follow the install guide there. The package is self-contained.

Which file do I download for Windows, macOS or Linux?

Each portable package in the download section is built for one computer. The guide pages linked under "Install on your computer" name the exact file and its size.

Published by schulzcode's Reborn project [1] [2]